Wednesday, September 25, 2013

InfoSewer Design of Existing Networks

InfoSewer can design either new or existing networks.  Here is an example of how it updates pipe sizes based on the results of an EPS simulation and d/D constraints.   The d/D for the two upstream gravity mains goes to 1 in the existing EPS simulation (Figure 1) and the velocity exceeds 10 ft/sec in the same two gravity mains (Figure 2).  We are going to use InfoSewer Design for an Existing system and resize the pipe sizes so that the maximum d/D is 0.80 and the velocity is between 1 and 6 feet/sec (Figure 3).  The design reports the needed new pipe diameters and cost (Figure 4) and then when the new pipe diameters are used in a new EPS solution the constraints for d/D are met and all pipes have a d/D value less than 0.80 (Figure 5).

Figure 1.  d/D for the Upstream Gravity Mains in the EPS Solution


Figure 2.  The Velocity for the Upstream Gravity Mains in the EPS Solution




Figure 3.  Design Options for the Existing System Design


Figure 4.  New Pipe Design diameters and d/D values


Figure 5.  After applying the new pipe diameters of 24 and 30 inches, respectively the d/D values do not exceed 0.80.


Tuesday, September 24, 2013

“Drawing Water”

“Drawing Water”

"Drawing Water"
David Wicks / Via sansumbrella.com
David Wicks’ “Drawing Water” is a constructed landscape visualizing where water falls and where it is consumed in the United States.

Innovyze President Dr. Paul F. Boulos Joins Board of Trustees of Academy of Coastal, Ocean, Port & Navigation Engineers

Innovyze Press Release
 Insider BlogLinkedInTwitterYouTubeYouTube
Innovyze President Dr. Paul F. Boulos Joins Board of Trustees of Academy of Coastal,
Ocean, Port & Navigation Engineers
Broomfield, Colorado, USA, September 24, 2013 — Innovyze, a leading global innovator of wet infrastructure modeling and simulation software and technologies, today announced that its president and chief operating officer, Paul F. Boulos, Ph.D., BCEEM, Hon.D.WRE, Dist.D.NE, F.ASCE, has been elected to the Board of Trustees of the Academy of Coastal, Ocean, Port & Navigation Engineers (ACOPNE) of the American Society of Civil Engineers (ASCE). His term will begin October 1, 2013.
Dr. Boulos is one of the world’s foremost experts on water resources and navigation engineering and the author of nine authoritative books and more than 100 technical articles on issues critical to the water and wastewater industry. He has received numerous honors from national and international scientific and engineering societies, governments, universities, and NGOs, including notable technical awards for excellence in scholarship from ASCE, the American Water Works Association and the U.S. Environmental Protection Agency (USEPA). He has received the U.S. Ellis Island Medal of Honor, one of America’s highest accolades; the Pride of Heritage Award from the Lebanese American Foundation; and the Lebanese American University Alumni of the Year Award. He was also inducted into the University of Kentucky College of Engineering Hall of Distinction, the highest honor the university bestows on its alumni. Dr. Boulos has been given Honorary Diplomate status by the American Academy of Water Resources Engineers (AAWRE) as well as Distinguished Diplomate status in Navigation Engineering by ACOPNE, the top honors for both academies. He is a Fellow of the American Society of Civil Engineers and a Diplomate (by Eminence) of the American Academy of Environmental Engineers.
Dr. Boulos serves on the Board of Trustees of the Lebanese American University (New York, NY, and Beirut, Lebanon) and AAWRE; the Boards of Directors of Innovyze, MWH Global (Broomfield, CO) and America-Mideast Educational and Training Services, Inc./AMIDEAST (Washington, D.C.); and the Dean’s International Council of the Harris School of Public Policy Studies at the University of Chicago (Chicago, IL). He has been a member of advisory boards and councils for many organizations, including the Buck Advisory Council of the Buck Institute for Research on Aging (Novato, CA), the USEPA Science Advisory Board, the Urban Water Resources Research Council of the Environmental and Water Resources Institute (EWRI), and the National Academy of Sciences/National Research Council.
Dr. Boulos received his Doctorate, Master of Science and Bachelor of Science degrees in Civil Engineering from the University of Kentucky, along with a Bachelor’s degree in General Science from the Lebanese American University. He has also completed Harvard Business School’s Advanced Management Program.
The Academy of Coastal, Ocean, Port and Navigation Engineers was created by ASCE and its Civil Engineering Certification, Inc. (CEC) to improve the practice, elevate the standards, and advance the COPNE-Profession for the benefit of the public. The elite group is comprised of nearly 200 Diplomates who have gone through many years of training and experience to become eligible for Board Certification. The Academy is a way to recognize engineers who have special knowledge and experience in the fields of civil engineering that comprise ACOPNE. 
The COPNE-Profession comprises the individuals and professional organizations that are engaged in the sustainable development and protection of coastal, ocean, port, and navigation environments for the benefit of society in the United States and foreign countries. ACOPNE has in part been created to complement the Coasts, Oceans, Ports, and Rivers Institute (COPRI) and provides recognition to those individuals who have excelled in one or more of the sub-disciplines embraced by COPRI. Key objectives are to identify and grant board certification to individuals with specialized knowledge; recognize the ethical practice; enhance the technical practice; support and promote positions on professional issues important to the public health, safety, and welfare; and encourage life-long learning and continued professional development.
“It’s an especially meaningful honor to be asked to serve on this distinguished board and be a member of this preeminent academy,” Boulos said. “I am proud to be a part of the noble COPNE profession and to be able to contribute to its advancement. Joining the distinguished leaders of ACOPNE gives me an exceptional opportunity to share my expertise and passion and make whatever contributions I can to help further the Academy’s vision and mission.”
For more information on ACOPNE, visit www.acopne.org.

Sunday, September 22, 2013

Cómo importar Enlace Shapefiles en InfoSWMM

Cómo importar Enlace Shapefiles en InfoSWMM

Cómo importar Enlace Shapefiles en InfoSWMM

Este blog se describe cómo utilizar la herramienta de puerta de enlace de los SIG en InfoSWMM importar shapefiles y hacer tablas DB InfoSWMM y Arc Mapa Capas de la Shapefiles. La importación de archivos de forma en cualquiera InfoSWMM o H2oMap SWMM es muy flexible y se utiliza el cambio Mando / GIS Gateway. Si usted está empezando desde un nuevo Arco Mapa entonces lo mejor es añadir primero los shapefiles de Arc Map, inicializar el Mapa para el Sistema de Coordenadas del Shapefiles e importar los archivos de forma utilizando GIS Portal para hacer una capa Junction InfoSWMM. Los pasos para utilizar el GIS Portal para nodos

Paso 1.    Agregar las tuberías o Link Shapefiles e inicializar el Arco del mapa al sistema de coordenadas del Shapfile usando cualquiera de las opciones de geodatabase personal o de archivos.
Paso 2.    Utilice el comando Portal GIS y configurar el archivo de forma de cargar en las tablas conducto de InfoSWMM con el campo adecuado Mapeo GIS.
Paso 3.    será necesario asignar los campos de datos shapefile InfoSWMM los campos de datos de conducto.
Paso 4.    Cargue el archivo de forma mediante el comando de carga. Las Tablas InfoSWMM DB se actualizará.
Paso 5.    La capa de Conduit de InfoSWMM tiene las tablas cargadas, se puede ver los datos utilizando el comando Abrir tabla de atributos.
Paso 6.    La Tabla DB InfoSWMM de conductos tiene el vínculo de datos importados.


Paso 1.    Agregar las tuberías o Link Shapefiles e inicializar el Arco del mapa al sistema de coordenadas del Shapfile usando cualquiera de las opciones de geodatabase personal o de archivos.




Paso 2.    Utilice el comando Portal GIS y configurar el archivo de forma de cargar en las tablas conducto de InfoSWMM con el campo adecuado Mapeo GIS.




Paso 3.    será necesario asignar los campos de datos shapefile InfoSWMM los campos de datos de conducto.


Paso 4.    Cargue el archivo de forma mediante el comando de carga. Las Tablas InfoSWMM DB se actualizará.

. Paso 5    La capa de Conduit de InfoSWMM tiene las tablas cargadas, se puede ver los datos utilizando el comando Abrir tabla de atributos.

Paso 6.    La Tabla DB InfoSWMM de conductos tiene el vínculo de datos importados.

How to Import Link Shapefiles into InfoSWMM

How to Import Link Shapefiles into InfoSWMM

This blog describes how to use the GIS Gateway tool in InfoSWMM to import shapefiles and make InfoSWMM DB Tables and Arc Map Layers from the Shapefiles.   The import of shapefiles into either InfoSWMM or H2oMap SWMM is very flexible and uses the Command Exchange/GIS Gateway.  If you are starting from a new Arc Map then it is best to first add the shapefiles to Arc Map, initialize the Map to the Coordinate System of the Shapefiles and then import the Shapefiles using GIS Gateway to make an InfoSWMM Junction Layer.  The Steps to use the GIS Gateway for Nodes

Step 1.   Add the Pipe or Link Shapefiles and Initialize the Arc Map to the Coordinate System of the Shapfile using either the Personal or File GeoDatabase Options.
Step 2.   Use the GIS Gateway command and set up the Shapefile to load into the Conduit Tables of InfoSWMM with the proper GIS Mapping Field.
Step 3.   You need to Map the Shapefile Data Fields to the InfoSWMM Conduit Data Fields.
Step 4.   Load the Shapefile using the Load Command.  The InfoSWMM DB Tables will be updated.
Step 5.   The Conduit Layer of InfoSWMM has the loaded tables, you can see the data by using the Open Attribute Table Command.
Step 6.   The InfoSWMM DB Table for Conduits has the imported Link data.


Step 1.   Add the Pipe or Link Shapefiles and Initialize the Arc Map to the Coordinate System of the Shapfile using either the Personal or File GeoDatabase Options.




Step 2.   Use the GIS Gateway command and set up the Shapefile to load into the Conduit Tables of InfoSWMM with the proper GIS Mapping Field.




Step 3.   You need to Map the Shapefile Data Fields to the InfoSWMM Conduit Data Fields.


Step 4.   Load the Shapefile using the Load Command.  The InfoSWMM DB Tables will be updated.

Step 5.   The Conduit Layer of InfoSWMM has the loaded tables; you can see the data by using the Open Attribute Table Command.

Step 6.   The InfoSWMM DB Table for Conduits has the imported Link data.




Cómo importar subcuencas de los SIG en InfoSWMM

Cómo importar subcuencas de los SIG en InfoSWMM

Cómo importar subcuencas de los SIG en InfoSWMM


Paso 1:   Agregar el archivo de formas utilizando el comando Agregar datos.
Paso 2:   Su archivo de forma importada no tiene datos subcuencas antes de inicializar el proyecto.
Paso 3:   Añadir los datos subcuencas mediante el intercambio GIS Import Cluster
Paso 4:   Ahora tienes las subcuencas en las tablas de datos y ahora se puede calcular el área.
=====================================
Paso 1:   Agregar el archivo de formas utilizando el comando Agregar datos.


Paso 2:   Su archivo de forma importada no tiene datos subcuencas


Paso 3:   Añadir los datos subcuencas mediante el intercambio GIS Import Cluster

  

Paso 4:   Ahora tienes las subcuencas en las tablas de datos y ahora se puede calcular el área.
Todavía tenemos que entrar en 1/10000 para obtener las unidades adecuadas para el área subcuenca mediante el cálculo del área bajo Auto Herramientas preferencias. En primer lugar, importa el archivo de forma y luego de encender Cálculo Area Auto, introduzca un valor para el factor de escala de área y luego usar las utilidades de la herramienta, actualización del DB Map, todo subcuenca para obtener el Area subcuenca en hectáreas.




Cómo importar archivos de forma de nodo en InfoSWMM

Cómo importar archivos de forma de nodo en InfoSWMM

Cómo importar archivos de forma de nodo en InfoSWMM

Este blog se describe cómo utilizar la herramienta de puerta de enlace de los SIG en InfoSWMM importar shapefiles y hacer tablas DB InfoSWMM y Arc Mapa Capas de la Shapefiles. La importación de archivos de forma en cualquiera InfoSWMM o H2oMap SWMM es muy flexible y se utiliza el cambio Mando / GIS Gateway. Si usted está empezando desde un nuevo Arco Mapa entonces lo mejor es añadir primero los shapefiles de Arc Map, inicializar el Mapa para el Sistema de Coordenadas del Shapefiles e importar los archivos de forma utilizando GIS Portal para hacer una capa Junction InfoSWMM. Los pasos para utilizar el GIS Portal para nodos

Paso 1.    Añadir la boca de acceso o nodo Shapefiles y Inialize el Arco mapa al sistema de coordenadas del Shapfile usando cualquiera de las opciones de geodatabase personal o de archivos.
Paso 2.    Utilice el comando Portal GIS y configurar el archivo de forma de cargar en las tablas de unión de InfoSWMM con el campo adecuado Mapeo GIS.
Paso 3.    será necesario asignar los Shapefile campos de datos a los InfoSWMM Junciton campos de datos.
Paso 4.    Cargue el archivo de forma mediante el comando de carga. Las Tablas InfoSWMM DB se actualizará.
Paso 5.    La capa Juction de InfoSWMM tiene las tablas cargadas, se puede ver los datos utilizando el comando Abrir tabla de atributos.
Paso 6.    La Tabla InfoSWMM DB para uniones con los datos Junction importados.


Paso 1.    Añadir la boca de acceso o nodo Shapefiles y Inialize el Arco mapa al sistema de coordenadas del Shapfile usando cualquiera de las opciones de geodatabase personal o de archivos.




Paso 2.    Utilice el comando Portal GIS y configurar el archivo de forma de cargar en las tablas de unión de InfoSWMM con el campo adecuado Mapeo GIS.




Paso 3.    será necesario asignar los Shapefile campos de datos a los InfoSWMM Junciton campos de datos.



Paso 4.    Cargue el archivo de forma mediante el comando de carga. Las Tablas InfoSWMM DB se actualizará.

Paso 5.    La capa Juction de InfoSWMM tiene las tablas cargadas, se puede ver los datos utilizando el comando Abrir tabla de atributos.

Paso 6.    La Tabla InfoSWMM DB para uniones con los datos Junction importados.

How to Import Node Shapefiles into InfoSWMM

How to Import Node Shapefiles into InfoSWMM

This blog describes how to use the GIS Gateway tool in InfoSWMM to import shapefiles and make InfoSWMM DB Tables and Arc Map Layers from the Shapefiles.   The import of shapefiles into either InfoSWMM or H2oMap SWMM is very flexible and uses the Command Exchange/GIS Gateway.  If you are starting from a new Arc Map then it is best to first add the shapefiles to Arc Map, initialize the Map to the Coordinate System of the Shapefiles and then import the Shapefiles using GIS Gateway to make an InfoSWMM Junction Layer.  The Steps to use the GIS Gateway for Nodes

Step 1.   Add the Manhole or Node Shapefiles and Inialize the Arc Map to the Coordinate System of the Shapfile using either the Personal or File GeoDatabase Options.
Step 2.   Use the GIS Gateway command and set up the Shapefile to load into the Junction Tables of InfoSWMM with the proper GIS Mapping Field.
Step 3.   You need to Map the Shapefile Data Fields to the InfoSWMM Junction   Data Fields.
Step 4.   Load the Shapefile using the Load Command.  The InfoSWMM DB Tables will be updated.
Step 5.   The Junction Layer of InfoSWMM has the loaded tables, you can see the data by using the Open Attribute Table Command.
Step 6.   The InfoSWMM DB Table for Junctions has the imported Junction data.


Step 1.   Add the Manhole or Node Shapefiles and Inialize the Arc Map to the Coordinate System of the Shapfile using either the Personal or File GeoDatabase Options.




Step 2.   Use the GIS Gateway command and set up the Shapefile to load into the Junction Tables of InfoSWMM with the proper GIS Mapping Field.




Step 3.   You need to Map the Shapefile Data Fields to the InfoSWMM Junction   Data Fields.



Step 4.   Load the Shapefile using the Load Command.  The InfoSWMM DB Tables will be updated.

Step 5.   The Junction Layer of InfoSWMM has the loaded tables, you can see the data by using the Open Attribute Table Command.

Step 6.   The InfoSWMM DB Table for Junctions has the imported Junction data.

GitHub code and Markdown (MD) files Leveraging

 To better achieve your goal of leveraging your GitHub code and Markdown (MD) files for your WordPress blog or LinkedIn articles, consider t...